How To Backwash Pool Filter Cartridge – In order to get the most out of your backyard swimming pool, it is important to clean and maintain the filtration system regularly. In this article, you will learn how to clean a pool filter and other useful pool maintenance tips.
Whether it’s an in-ground or above-ground pool, your pool maintenance process becomes much easier when you know how to properly care for the filtration system you have.
How To Backwash Pool Filter Cartridge
To keep your pool water clean and clear, it is very important to clean the pool filters before they become too clogged or dirty. As your pool pump circulates water through the final system, dirt and debris particles become trapped in the filter.
Black Diamond Cartridge Filters And Systems From
Microscopic contaminants such as algae, bacteria, body oil and sunscreen are also removed. Therefore, it is important to regularly clean the filter of all accumulated debris to maintain a stable water flow level and prevent freezing.
Part of in-ground and above-ground pool maintenance is keeping the filter clean. This is an easy task if you have water-friendly plants and trees as part of your landscape.
The best way to clean your pool filter depends on several factors: the type of filter you have, how often you use your pool, what your climate is like, and whether or not you have hard water.
Always read the cleaning instructions for the specific pool filter carefully before performing any maintenance procedures to avoid accidental damage.
Pentair Clean & Clear Plus Cartridge Filter
There are three basic styles of pool filters: cartridge filters, sand filters, and diatomaceous earth, or DE filters. Each type of processing system has unique advantages and different maintenance procedures.
Read on to learn all about cleaning a pool filter cartridge, sandblasting or DE filter, and extending the service life of your pool filter.
If you are trying to clean a green pool, cleaning the filter is an important part of the process.
Cartridge filters, such as the Hayward, are the most common type of pool filter used because they are efficient and straightforward to maintain. They are also more environmentally friendly as they require less water use during the cleaning process.
Clean & Clear Aboveground Cartridge Filter System
A cartridge filter works by pumping pool water through a rotary filter cartridge made of absorbent polyester fabric. The cloth traps particles in the water and collects smaller particles than other pool filters.
There are different methods when it comes to how to clean a pool filter cartridge. Choosing one depends on how dirty the filter is and the material available.
Close the pool pump in the wash, and bleed air from the system using the pump’s air relief valve, usually on top of the filter.
Remove the top of the filter. Consult your owner’s manual to make sure you don’t accidentally damage the filter housing.
Hayward Swimclear Cartridge 325 Sq. Ft. Pool Filter, W3c3030 (hay 05 822)
After removing the pool filter cartridge, inspect it carefully for signs of wear, tears, or other damage. If the filter is damaged, you need to replace it.
Also check the o-ring on the filter tank. If you notice any cracks, dryness, or vibration, replace it. However, use a non-oily moisturizer to prevent drying before your next cleaning.
Using your garden spray nozzle at an angle works best to reach between the filter cloth plates. Avoid using a pressure washer, as this is likely to damage the cartridge.
It is possible to use dishwasher detergent to clean your pool filter cartridge. Mix one cup of detergent per five gallons of water and soak the filter for three to ten hours.
Cartridge Filter: Jandy Pro Series Cv Cartridge Filter
Use the spray nozzle attachment on your garden hose to rinse the cartridge until the water is removed before reassembling your pool.
If your pool filter is dirty, soak the cartridge in a cleaning solution of vinegar and water for a few hours. The acidic nature of vinegar is great for washing away algae as well as bacteria and calcium deposits in pools.
Vinegar is safer and more environmentally friendly than muriatic acid, which can cause serious chemical burns and lung damage if it comes into contact with your skin and eyes, or if you inhale the fumes.
After rinsing, place the filter cartridge in a large bucket and fill it with a clean solution of equal parts water and distilled white vinegar. Soak the filter for three to ten hours.
How To Clean Different Pool Filters
About halfway through the soaking time, turn the filter in the bucket to make sure all parts of the filter are exposed to the hot solution. After drying, rinse the filter again before installation.
Sunscreen and body oil are difficult to remove from your pool filter cartridge. However, using a stiff bristle brush on your filter cartridge to remove debris can damage the polyester or paper plates.
To remove stubborn residue, be sure to use a soft bristle brush specially designed to clean cartridge filters to prevent accidental damage to the cartridge.
In a five-gallon bucket, mix the ingredients and place your filter cartridge in the cleaning solution. Bake for three to ten hours. After drying, rinse the cartridge before resetting the filter system.
Evoclear Opal (op) Series Cartridge Filter
Always check your filter care manual and warranty information before using DIY cleaning products to make sure you won’t damage the product or void the warranty.
Sand filters are the most affordable pool filters. Pool water is pumped through a filter tank filled with silica sand, which traps dirt and debris before pumping clean water back into your swimming pool.
Although they are economical, easy to maintain and durable, they are not very effective in removing small particles in water.
The average sand filter has a micron filtration rate of 20-40 ppm, while a cartridge filter usually has a micron filtration rate between 5-20 ppm.
Backwashing Your Swimming Pool Filter: A Complete Guide
Always refer to the specific care instructions for your pool filter when cleaning to avoid accidental damage.
To determine when to clean your sand filter, pay attention to the pressure level of the system. Most filtration systems operate between 5-20 psi. Check the owner’s manual for any specific recommendations for your system.
Turn off the sand filter when the filter pressure gauge reads eight to ten psi above the average level. Turn off your pool pump, and turn the valve to the ‘backwash’ position.
Turn the pump back on and flush the system for at least two minutes or until the water in the filter window is clear. When backwashing, slowly add the sand cleaner to the skimmer.
Vevor Pool Cartridge Filter 8.8 In. Dia Replacement Filter Cartridge 100 Sq. Ft. Inground Pool Filter For Swimming Pool Ycglqzqxbl100p9tsv0
After the initial backwash is complete, turn off the pump and turn the filter valve to the ‘rinse’ setting.
Turn the pump back on and wash the filter for at least one minute. Finally, turn the pump and filter valve back to the ‘filter’ position, and turn the pump back on.
In general, the sand in your pool filter should be replaced every three to five years. However, the service life of the silica sand filter depends on how often you use the pool, the level of oil and grease in the water, and if you have hard water.
If you notice that your filter is running slowly or erratically, or that the back-up cycles are shorter than usual, it is possible that your filter sand is dirty and clogged.
What Types Of Filters Are Used To Treat Swimming Pools? By Clearion
With excess oil and grease production, the sand sticks together, and water cannot pass as intended. Instead, it forms a channel along the covered sand and returns to the lake without sedimentation.
Diatomaceous Earth, or DE filters, are the most effective pool filters, although they are the most expensive. The DE filter works like a sand filter.
The pond water is pumped through a fine white sediment made from the fossils of single-celled aquatic plants called diatoms. DE powder filters the smallest particles in water down to four microns.
Also, DE filters are more energy efficient, using less pool water pumping power through DE powder better than other filters. Like sand filters, DE filters are built-in. However, a few additional pieces of the DE processing system still need cleaning.
How To Backwash A Sand Filter
Clean your DE pool filter whenever the pressure gauge reads eight to ten psi above average level. Always read the specific maintenance recommendations for your pool filter in the owner’s manual to prevent accidental damage.
The first step in cleaning your DE filter is to perform a backwash to remove excess debris. Turn off your pool pump, and turn the valve to the ‘backwash’ system.
Reset your pool pump and run the backwash cycle until the water coming out of the drain hose runs clear. Close the pump again and return the filter valve to its normal position.
Open the air relief valve and remove the drain plug to empty the filter tank. Once dry, open the filter tank according to your owner’s manual and remove the manifold.
How To Backwash A Sand Filter For A Super Clean Pool
Take out the nets and wash them with your garden hose. Also wash the inside of the filter tank with a garden hose.
After lubricating the o-ring or gasket, replace the tank cover filter and release excess air through the air relief valve. Turn on your pool pump, and close the air relief valve after the water has drained. Pool pump must be running before adding DE powder.
Check your owner’s manual for the exact amount of DE powder to add.
Backwash cartridge pool filter, how to backwash a cartridge filter, how to backwash cartridge filter, backwash a pool filter, cartridge filter backwash, how to backwash a cartridge pool filter, pool filter backwash valve, backwash hayward cartridge pool filter, backwash hayward pool filter, how to backwash a hayward cartridge pool filter, how to backwash your pool filter, pool filter backwash hose